φ3.8×(6.5+3)m Technical performances of air swept coal mill
一、Technical parameters
Sepc. : φ3.8 x (6.5+3)m
Length of drying chamber:3m
Length of grinding chamber:6.5m
Capacity: 40t/h
Inlet grain size:≤25mm
Fineness of product: blind coal: R80μm Residue ≤5%
Material moisture content:Mill inlet≤10 %;Mill outlet≤1 %;
Mill rotating speed: 16.7r/min
Mill inlet air temperature:300℃(max350℃)
Mill outlet air temperature:60-100℃
Cooling water consumption
Cooling water consumption of main bearing:2 m3/h;
Cooling water consumption of slide shoe bearing:3.5 m3/h;
Cooling water consumption of thin oil station of main bearing:1.5 m3/h;
Cooling water consumption of thin oil station of slide shoe bearing:3.8 m3/h;
Cooling water consumption of lubrication station of main reducer:5.7 m3/h;
Cooling water consumption of lubrication station of main motor:1 m3/h;
Transmission device
Main motor
Type:YRKK7101-8 (Protection class:IP 54; Insulation class:F )
Power: 1250 kW
Rotating speed:742 r/min
Voltage:10 KV
Main reducer:
Type: MBYX800
Shaft location: (supply with lubrication station)
Speed ratio: I= 5.6
Slow driving reducer
Type: YNS620-90ⅡR
Power:22
Speed ratio:90
Reducing motor (for slow driving)
Type: Y200L2-6
Power: 22kW
Rotating speed: 970r/min
Voltage: 380 V
High pressure start & lubrication station (for discharge port of hollow shaft)
Type:NC-25S
Motor Y100L1-4 (High pressure oil pump for starting) 1pc
Power: 22 kW
Voltage:380V
Motor Y90L-4 (for low pressure oil pump of lubrication station) 2pcs
Power: 1.5 kW
Voltage:380 V
Electrical heater (for high pressure start & lubrication station)
Power: 2kW×3
Voltage: 220 V
High pressure start & lubrication station: (slide shoe bearing of feed port)
Type:NC-63S
Motor Y100L1-4 (for high pressure oil pump start) 2pcs
Power: 2.2 kW
Voltage:380 V
Motor Y112M-6 (for low pressure oil pump of lubrication station) 2pcs
Power: 2.2 kW
Voltage:380V
Electrical heater (for high pressure start & lubrication station)
Power: 3kW×4台
Voltage: 220 V
二、Material quality of main parts
1、Shell Q235-B δ34mm
2、Main motor YRKK7101-8 10KV
3、Main reducer MBYX800
4、Hollow shaft:ZG230-450
5、Pinion:35CrMo
6、Pinion shaft:35CrMo
7、Supporting:
Bush body Cast steel
Bush liner (Barritt ZChSnSb11-6)
Base: cast steel
8、Liner: cast steel alloy
三、Supply range:
Seller supply full set equipments except grinder & main control
1、Rotary section |
1 set |
2、Feed device |
1 set |
3、Main bearing device |
1 set |
4、Slide shoe bearing of sliding end |
1 set |
5、Discharge device |
1 set |
6、Liner & double diaphragm device |
1 set |
7、Main motor YRKK7101-8 1250KW 10KV |
1 pc |
8、Main reducer MBYX800 |
1 pc |
9、Auxiliary driving |
1 set |
10、Thin oil station GYXZ-63A |
2 pcs |
11、Coupling |
1 set per pc |
12、Anchor bolts |
1 set |